35 vintage black and white bathroom tile ideas and pictures

Vintage Bathroom Tiles White Tile Bathrooms Designs Black 35 vintage black and white bathroom tile ideas and pictures

Bathroom Renovation - A Step by Step Guide

Bathrooms are some of the smallest rooms in the house plus they are also one the most expensive for renovate. Bathroom renovation is a job that, if done well, may add value to your home and a great space packed with design and light-weight.

Bathroom design
Bathroom design could be the first part of a bath room renovation you should get right. Just replacing the existing bathroom with the same design might not be enough. The key to great bathroom design would be to design it while using individuals who are likely to utilize it in your mind. However make certain that your bathrooms design also offers a general use factor at the same time.

For example: If you were designing your bathrooms for families you can still design the restroom with quick access to the shower and bath. This would be sure that the style would also work if you have limited mobility. This means if you sell your own home or if you are renovating for profit your design carries a wider market appeal. Great bathroom design also uses space well, taking into account the sunlight or window space, size of fittings, and drainage options. Draw out a strategy to scale and right down the sizes of the room. Mark the prevailing drainage points and after that and water inlet points. Write down a wish listing of the restroom fittings to require and desire with their sizes. Now marry the 2 together and discover what fits. Note: Most bathroom drainage and water inlet points can be moved but this will come at extra cost.

Bathroom remodel
If you have chosen to perform the project yourself or part of the task it can be time to engage a skip bin and grab the existing bathroom. If your house is made pre 1980 you could have fibro bathroom wall linings with asbestos inside it and great care should be taken. You will need some full body disposable overalls, eye protection, and quality dust mask. Check with your neighborhood building authority or council in connection with regulation on bathroom asbestos wall lining removal.
Remove everything except the plumbing. If you keep the restroom plumbing available you do not have to turn the water off for the complete house. Also you will likely need to jack hammer the floor tiles up and also the sand and cement bed that they are laid on.

Bathroom Renovation and construction
Bathrooms must be construction properly from your start to ensure that the finished job is correct and true. This also ensures the design and look of the restroom can have a fantastic finish

The Bathroom Renovation Process

Install water and drainage pipe and electrical wires.

Install wall lining and ceiling and then install the bathtub hob and bath.

Waterproof the floor and shower and bath recess.

Correct late the bottom with sand and cement ready for tiling.

Lay floor and wall tiles and after that grout.

Install new bathroom vanity, fittings, and taps - install new electrical.

Paint ceiling and final  one - Plumbing and electrical
At this aspect brand new plumbing is installed for clean hot and cold water and drainage. Careful attention should be taken when positioning the brand new plumbing in order that the plumbing fittings are correct once the tiling is fully gone. For example: To centre a fitting in the shower recess you have to take into account the thickness with the wall board, tile glue and tile therefore the fitting will probably be centred following your tiles are set up. The same pertains to installing drainage pipes for any toilet; the wall lining and tile thickness has to be considered and so the pipe is incorporated in the correct position when the toilet is installed after tiling. Also rough within the any new electrical wires without connecting them on the mains power.

Step two - Install wall and ceiling linings
Install your 6mm wall lining being careful to nail the fibro board every 150mm without nailing into the new pipes and electrical wires. The best way is usually to measure and mark the pipe and wire layout on to your new wall board which has a pencil because you go. Screw up (or nail) the ceiling lining, plasterboard could be the most common. However if you are laying your tiles from floor to ceiling don't install the cornice because most effectively achieved after tiling. If you happen to be not tiling to the ceiling proceed to install the cornice following your wallboard and ceiling lining have been installed. Also if your bath just isn't freestanding you can now make up the frame and install the bath. Ensure the bathtub is installed correctly permitting the thickness of the tiles and  sure to check all linings and pipes when you continue with your bathrooms renovation.

31 retro black white bathroom floor tile ideas and pictures

Step three - Waterproof your bathroom
Waterproof a bath room floor, shower recess, and around the bathtub. When waterproofing the bottom make certain that the waterproofing comes 100mm up the walls. The shower recess will have to be waterproofed 100mm across the shower rose outlet. Also the bath ought to be waterproofed 100mm higher than the lip with the bath right around and to the floor. At the doorway install a 25 x 25mm aluminum angle glued into place with quality silicone and waterproof in to the lip. Your whole bathroom should now the tanked, hence the all water will still only drop a drain. Bathroom waterproofing tip: waterproofing is a simple job but quality and accuracy is most important.
Step four - Lay within the cement screed for the floor.

Before a floor tiles can laid the ground has to be smooth and fairly flat having a slight fall to the drainage outlet. To do this you should use sand and cement mix which is far better to add a waterproofing agent into this too. With a level, set a floor level in the doorway. Use the top aluminum angle because the finished floor level and measure around the thickness with the tile plus 10mm for that glue. Mark right around the lavatory using a level then screed inside your sand and cement mix using a 1 to 3 degree fall to the top with the drain outlet. Take your time and get it right while using finished level as smooth as possible. When the sand cement mix has set but is just not dry (you'll be able to walk into it however, you it is a little soft) rub it over using a house brick. This will remove all the small highs and lows and look having a level when you go. Let the bathroom floor fully dry and after that you must have a fantastic surface to tile onto. Tip: the harder work you add into the ground screed the easier your tiling will likely be.

15 Gorgeous Black and White Tile Bathroom Design Ideas EVA Furniture

Step five: Tile floor and walls
Lay your tiles on the ground first after which grout. Then lay your wall tiles making certain actually level because you lay. Once the restroom tiles are actually cut and laid, grout all your tiles then buff the tiles clean.
Step six: Install plumbing fitting and fixtures
Install all your plumbing fittings and taps. Also fit your entire towel rails and soap holders. Fit your brand-new bathroom vanity making certain it really is level and sealed around the top with silicone plus seal around the bathtub. Tip: make sure they have been in the right place prior to deciding to drill to your tiles.

Best 25+ Black white bathrooms ideas on Pinterest Black and white tiles bathroom, Classic

Step seven: painting, and cleaning - enjoy
Paint your ceiling and execute a final clean ensuring that things are fitted correctly and that there isn't any leaks inside your plumbing. - Enjoy your brand-new bathroom.